Whole Lotta Round

In Arthur Ransomes Swallowdale, the Swallows are shipwrecked in a gale when Swallow gibes unexpectedly, and runs herself on to Pike Rock. Shes holed and her mast breaks off just above the thwart. Disaster! But the Swallows are good swimmers (life jackets not having been invented, yet), all make it to shore safely (Captain John abandoning ship only seconds before she sinks), and even manage to salvage Swallow and her cargo (except for the bread, which is ruined, in Susans opinion.)

Whew. Just another day in the life of our intrepid adventurers. After patching the hole in Swallows planking, and sailing her to the boatbuilders to be repaired (imagine a small, lakeside town in rural England with several boatbuilders to choose from!), Captains Flint and John commence building a new mast for Swallow.

Captain Flint (in his dreams!) roughing out Swallows mast. 

This is to be a proper mast, carved from the heartwood of a Norway pine. Captain Flint roughs it out with an adz, and then he and John use a big pair of calipers and something called they called a shaping plane, to shape and smooth the new mast.

Using the broken mast as a guide, they take measurements with the calipers, and then use the shaping plane to replicate the tapered shape of the old mast.

What didnt strike me until this week was how long this shaping took. John & Captain Flint worked all day (meaning sun up to sundown, which is a long time in an English summer) for several days at this work. And that was before they used up a whole roll of sand paper getting the mast as smooth as the original.

Unfortunately, shaping plane was a generic term used to describe many different types of planes, so its difficult to say what sort of plane they used, but I suspect it had a hollow sole, and a concave blade, so it could take off a wider shave on a round surface than a straight blade can.

I didnt have such a plane, alas, so had to do a very similar job with my spokeshave. A job, as I should have guessed from reading Swallowdale, that took a very long time!

The first job was to 16 side my 8-sided spar. Heres a video with the general approach.



After the spar was 16-sided, it was a simple job to make it round, with a few more (hundred) strokes from the spokeshave. By this time, I was an expert at sharpening this tool!

I then had a round spar that was about 1/4" too thick. Id purposefully left it oversized so that I would be able to trim it down to the right size. As Captain Flint told John: "Remember one thing.  Never take off too much. If you take off too little, you can always take off a bit more, but if you take off too much you can never put it back."

What he didnt say was how long it took to take off "a bit more". A quarter inch doesnt sound like much, but believe me, it is, when you can only remove a thin shaving that is only 1/8" wide.

My first priority was to shape the in-board end of the spar to the right diameter, so it could fit through the hole in the Blue Moons transom. Before I spent days shaving the rest of the spar, I wanted to do a test fitting, to make sure the boomkin would actually curve around the outboard engine, the way I expected it to. If it didnt, then the whole project was a waste of time.

The hole in the transom was 2 1/4" wide, so I made a template from a piece of plywood, by drilling a 2 1/4" hole in it. Inch by inch, I shaped the end of the spar so it would fit the template.

I coated the inside of the template hole with graphite to make it easier to see the high spots on the spar.

To do this, I just ran a pencil around the inside of the template, then pushed the template onto the spar.

Rounding spar to correct size with a template, coated with graphite
from a pencil

After removing the template, the high spots were marked with graphite. I then used my spokeshave to remove the graphite, and the wood underneath.

The result? A round spar of the correct diameter.

Its a slow, but sure process.

Graphite marks show the high spots that need to be removed.

After trimming enough of the end to fit, it was time to cart the spar out to the dock for a trial fitting. I must say I was worried by this time that the whole exercise would be a failure, so I was really please that it fit into the transom perfectly and -- more important -- the spars curve was exactly what Id hoped for.

The photo below shows how the new spar now curves around the space needed by the outboard. Exactly as Id hoped for.

Actually, the angle of the photo doesnt show how much extra space there is, very well, but trust me, its a lot. I should have brought the old boomkin down and taken a contrasting photo, but I didnt think of this. Ill try to take a couple more photos of the old and new curves, the next time I go down to the dock for a fitting. But the old boomkin curved right over the top of the outboard.

Test fitting of new spar

So, I am really pleased with the way this is coming out, but I am rapidly running out of time. I lose my dock space on April 1, so I must quickly bend and laminate the second spar, while I continue to shape and smooth the first. The job will be a lot more difficult if I have to row out to my mooring to work on it, so Im determined to finish the job in a couple weeks.



>>> Next Episode: Back to Square

Related Posts by Categories